# IronRut: full details > IronRut makes tough replacement parts for equipment when the original part is hard to find or discontinued. Parts are 3D printed in tough engineering plastic and finished in a small New Hampshire shop. Website: https://ironrut.com/ Where to buy: eBay Contact: message the seller through the eBay listing (https://www.ebay.com/itm/168871981504) Location: New Hampshire, USA Not affiliated with or endorsed by Kubota. Kubota is a trademark of Kubota Corporation. ## Product: Mid PTO Dust Cover for Kubota B2150, B1550, B1750 - Page: https://ironrut.com/products/kubota-mid-pto-dust-cover/ - Buy on eBay: https://www.ebay.com/itm/168871981504 - eBay title: Mid PTO Dust Cover fits Kubota B2150 B1550 B1750, Stops Grass Wrap, Bolt-On - Brand: IronRut - MPN (manufacturer part number): IR-MPTO-01 - Price: $37.95 USD. Buyer pays shipping. Best Offer is off. - Condition: New - Ships: in 1 to 3 business days, USPS Ground Advantage - Returns: 30 days, buyer pays return shipping ### What it does On the Kubota B2150, the mid PTO (power take-off) stub spins any time the rear PTO is running. Grass and chaff wrap around the bare splines, and that buildup can damage the seal. This bolt-on cover encloses the stub so grass has nothing to grab. ### Benefits - Helps protect the seal: grass and chaff stay off the spinning splines. - Bolt-on, no drilling: uses the factory bottom bolt hole. - Stays put: the bolt plus 5 built-in magnets hold the cover so it will not shift. - Plenty of clearance around the shaft. Test-fitted on a B2150. - UV-resistant 3D-printed ASA plastic for outdoor use. - Fits either thread: includes both a 5/16-18 and an M8 x 1.25 stainless steel bolt. ### Kit contents - 1 dust cover with 5 built-in magnets on the mounting face - 2 stainless steel bolts: 5/16-18 and M8 x 1.25 - 1 stainless steel washer ### Fitment - Kubota B2150 (tested) - Kubota B1550 (same mid PTO case) - Kubota B1750 (same mid PTO case) Verify fit on your own tractor before use. ### Size - Overall: 4.25 x 3 x 3.5 in - Inside depth: 2.5 in - Bore: 1.5 in - B2150 stub measured about 1 in diameter with 1.75 in protrusion ### Install 1. Engine off, key out. 2. Remove the bottom bolt. 3. Set the cover over the stub. 4. Use whichever bolt threads in by hand, with the washer, and snug it. Never force it or re-tap. ### Safety Dust cover only, not a safety shield. Remove before using a mid PTO implement. ### FAQ Q: Will this fit my Kubota tractor? A: It is made for the mid PTO (power take-off) on the Kubota B2150, B1550 and B1750. It was test-fitted on a B2150, and the B1550 and B1750 use the same mid PTO case. The B2150 stub measured about 1 in across with about 1.75 in sticking out, and the cover has a 1.5 in bore and 2.5 in of inside depth, so there is plenty of clearance. Please verify fit on your own tractor before use. Q: How do I install it? Do I need to drill anything? A: No drilling. It uses the factory bottom bolt hole. With the engine off and the key out, remove the bottom bolt, set the cover over the stub, then thread in whichever included bolt fits by hand, with the washer, and snug it. Q: Why does the kit come with two different bolts? A: So it fits either thread. You get one 5/16-18 and one M8 x 1.25 stainless steel bolt. Use whichever one threads in by hand. Never force a bolt or re-tap the hole. Q: What are the magnets for? A: The 5 built-in magnets on the mounting face add holding force. The bolt plus the magnets keep the cover from moving or shifting. Q: What is it made of, and will it hold up outdoors? A: The cover is 3D printed in ASA, a UV-resistant engineering plastic chosen for outdoor use. A specific temperature rating is not published yet. If you have a heat question for your setup, message us on eBay before you buy. Q: What's included in the kit? A: One dust cover with 5 built-in magnets, two stainless steel bolts (5/16-18 and M8 x 1.25) and one stainless steel washer that spreads the load. The photos show the single cover from two angles. Q: Can I leave it on when I use a mid-mount mower or other mid PTO implement? A: No. Remove the cover before using a mid PTO implement. It is a dust cover only, not a safety shield. Q: How much is shipping, and can I return it? A: It sells for $37.95 on eBay and the buyer pays shipping, which eBay shows at checkout. It ships in 1 to 3 business days by USPS Ground Advantage. Returns are accepted within 30 days, and the buyer pays return shipping.