IRONRUT

IronRut · MPN IR-MPTO-01

Mid PTO Dust Cover

Fits Kubota B2150 • B1550 • B1750

Keep grass off your mid PTO (power take-off) shaft and help protect the seal.

On the B2150, the mid PTO stub spins any time the rear PTO is running. Grass and chaff wrap around those bare splines, and that buildup can damage the seal. This bolt-on cover encloses the stub so grass has nothing to grab.

$37.95

Sold on eBay. Buyer pays shipping. Ships in 1 to 3 business days.

  • Helps protect the seal. Grass and chaff stay off the spinning splines.
  • Bolt-on, no drilling. Uses the factory bottom bolt hole.
  • Stays put. The bolt plus 5 built-in magnets hold the cover firmly so it won't shift.
  • Plenty of clearance. Lots of room around the shaft. Test-fitted on a B2150.
  • Built for outdoors. 3D printed in UV-resistant ASA.
  • Fits either thread. Comes with a 5/16-18 and an M8 x 1.25 stainless steel bolt.

WHAT'S IN THE KIT

  • Dust cover with 5 built-in magnets on the mounting face for extra holding force
  • Two stainless steel bolts (5/16-18 and M8 x 1.25), so it fits either thread
  • Stainless steel washer that spreads the load

FITS

Kubota B2150Tested
Kubota B1550Same mid PTO case as the B2150
Kubota B1750Same mid PTO case as the B2150

Please verify fit on your own tractor before use.

EASY INSTALL

  1. Engine off, key out.
  2. Remove the bottom bolt.
  3. Set the cover over the stub.
  4. Use whichever bolt threads in by hand, with the washer, and snug it. Never force it or re-tap.

SIZE & SPECS

Overall size4.25 x 3 x 3.5 in
Inside depth2.5 in
Bore1.5 in
B2150 stub (measured)About 1 in diameter, 1.75 in protrusion
MaterialUV-resistant 3D-printed ASA
HardwareStainless steel bolts (5/16-18 and M8 x 1.25) and washer
MPN (manufacturer part number)IR-MPTO-01

FAQ

Will this fit my Kubota tractor?

It is made for the mid PTO (power take-off) on the Kubota B2150, B1550 and B1750. It was test-fitted on a B2150, and the B1550 and B1750 use the same mid PTO case. The B2150 stub measured about 1 in across with about 1.75 in sticking out, and the cover has a 1.5 in bore and 2.5 in of inside depth, so there is plenty of clearance. Please verify fit on your own tractor before use.

How do I install it? Do I need to drill anything?

No drilling. It uses the factory bottom bolt hole. With the engine off and the key out, remove the bottom bolt, set the cover over the stub, then thread in whichever included bolt fits by hand, with the washer, and snug it.

Why does the kit come with two different bolts?

So it fits either thread. You get one 5/16-18 and one M8 x 1.25 stainless steel bolt. Use whichever one threads in by hand. Never force a bolt or re-tap the hole.

What are the magnets for?

The 5 built-in magnets on the mounting face add holding force. The bolt plus the magnets keep the cover from moving or shifting.

What is it made of, and will it hold up outdoors?

The cover is 3D printed in ASA, a UV-resistant engineering plastic chosen for outdoor use. A specific temperature rating is not published yet. If you have a heat question for your setup, message us on eBay before you buy.

What's included in the kit?

One dust cover with 5 built-in magnets, two stainless steel bolts (5/16-18 and M8 x 1.25) and one stainless steel washer that spreads the load. The photos show the single cover from two angles.

Can I leave it on when I use a mid-mount mower or other mid PTO implement?

No. Remove the cover before using a mid PTO implement. It is a dust cover only, not a safety shield.

How much is shipping, and can I return it?

It sells for $37.95 on eBay and the buyer pays shipping, which eBay shows at checkout. It ships in 1 to 3 business days by USPS Ground Advantage. Returns are accepted within 30 days, and the buyer pays return shipping.

Dust cover only, not a safety shield. Install with the engine off and key removed. Remove before using a mid PTO implement. Verify fit on your model before use. Not affiliated with or endorsed by Kubota.

$37.95 · Mid PTO Dust CoverBuy on eBay